Select a Category
Build Author jnsbanman Views 269
A new design of my based on a couple different machines I have seen both on openbuilds and youtube. In the end will have a and X/Y workspace of 1250mm x 1000mm and a Z axis range of about 200mm.
Build Author David Bunch Views 252
V-Slot 2020 EggBot
To build a simple EggBot
Build Author Ariel Yahni Views 29773
Modifying the K40 laser cuter stock gantry in favor of OpenBuilds superior and smoother movement. Also will provide me a better level control for easier beam alignment.
Build Author SORIN ILIESCU Views 6484
Sphinx 55 on MGN12 linear rails
My machine is a combination of the Openbuilds Sphinx 55, MGN12 linear rails knockoffs and custom made plates made by Chris Laidlaw
Build Author HuguesP Views 5538
Yet Another Chinese Linear Rail CNC, my first one, doing this mainly for the fun of building it more than using it.
Build Author mathom713 Views 298
27" by 40" CNC
DIY design and build of a roughing 2' by 3.5' CNC router
Build Author GinoTheCop Views 462
A 1000 by 1000 CNC Router with linear rails and a control box.
Build Author David Florian Views 727
Dual Extruders 3D Printer - Zidex Upgraded
How to build an Independent Dual EXtruder (IDEX) 3D printer from OpenBuilds parts.
Build Author Kims3DIY Views 7589
Beamlazer Laser cutter CO2 100W
Hi everyone, im new to the world of lasercutters but i have been granted access for a Trotec laser for a while with old firmware and only compability trought Windows XP. Then i decided to build my own laser, with some easier workflow and support for Windows 10. Since im still a student i have limited resources, so i will try too use scrap parts as much as possible. I will publish photos and updates during my build continously. Gladly taking advices from others.
Build Author pedrofernandez Views 9754
Openbuilds Table Top 50w Co2 Laser Cutter/Engraver
DIY build of a Co2 Laser cutter/engraver 12x24 working area.
Build Author sausagePaws Views 1690081
DIY Embroidery Machine V2
My second attempt at an affordable sewing machine embroidery add on. This one uses readily available electronics modules and 3D printable parts where possible.
Build Author MattR Views 3523
Cricut Expressions 2 to ESP32 GRBL Control
A log of my "brain surgery" on a Cricut Expressions 2 to change the control board to something open so that I could cut what I wanted. The ESP32 GRBL board I used has bluetooth and WIFI built-in and was very easy to get working just the way I wanted.
Build Author pedrofernandez Views 4145
The Franken Rotor
Yes another K40 Franken machine dedicated for round objects,,,
Build Author Mark Carew Views 914016
OpenBuilds OX CNC Machine
OpenBuilds OX CNC Machine. A strong easy to build shop CNC router that can be sized to suit your needs. Many new features have been incorporated into the OX to make it a great router that is sure to inspire!
Build Author wackocrash5150 Views 1250
45W CO2 Laser Build
A co2 laser build that is heavily inspired and based quite a bit off Pedro Fernandez' 50w co2 laser build. This is my first build post so, bare with me.
Build Author Mark Carew Views 2549
A simple to assemble, super clean and safe PSU case solution that fits into the OpenBuilds wire management ecosystem
Build Author SecretSpy711 Views 11064
Heavily upgrading my 1200x500 Shapeoko 2... ...er, wait, scratch that... Building an all new machine, roughly the same size, that should be more rigid than a Shapeoko 3!
Build Author pedrofernandez Views 5675
Co2 Laser Cutter/Engraver Rotary Attachment
Vslot rail system at work again, laser cutter/engraver rotary device for cylindrical objects .
Build Author Mark Carew Views 5448
V-Slot™ Nema 23 Linear Actuator (Belt Driven)
This example build shows how easy it is to make a linear actuator using a few OpenBuilds Parts.
Build Author Kyo Views 103842
A strong desktop cnc router that will enable you to make larger aluminium plates without taking up to much room. Simple, strong and opensource ! Build one today..
Build Author Marco964 Views 1384
Lead CNC 1510 modified
This is an Openbuilds LEAD 1510, modified to supports a liquid cooled 1.5Kw spindle. The movements are made with lead screw on all three axes.
Build Author megashub Views 11421
K40 C02 Laser Rail System
An Openbuilds replacement rail system for the common eBay "K40" C02 Laser Cutter
Build Author Mark Carew Views 43493
V-Slot NEMA 23 Linear Actuator (Lead Screw)
Learn to build a super strong nema 23 lead driven linear actuator
Build Author Mark Carew Views 5169
Nema 23 Belt and Pinion Actuator
This easy to build and effective system can take your builds to the next level! This design is strong and accurate and could be the solution/upgrade that you've been looking for!
Build Author Mark Carew Views 3666
C-Beam XLarge X/Y Table
This OpenBuilds C-Beam XLarge X/Y Table is a great display of how easy it is to modify and create awesome configurations with the OpenBuilds system!
Build Author tmadrms Views 1113
C-beam machine mods.
Build Author MattR Views 5679
Fixed Gantry CNC Router with Old Industrial Supplies
I got lucky enough to purchase aluminum extrusions and linear motion components (and nuts/bolts/etc) at scrap metal prices when a bunch of industrial automation equipment was decommissioned. The only problem is that the aluminum extrusions are not metric sizes... they are the 1.5"x3" 80/20 series. It has presented a few challenges but nothing too bad.
Build Author Keith Davis Views 17742
TrueUp Kit Version
A Cartesian printer using bushings for the Z axis instead of wheels or linear bearings. The design also synchronizes two Z axis screws with a timing belt for a level lift. The ratio of the drive pulley and Z axis pulleys produce .005 lift per full step on a 200 step motor, eliminating layer resolution "drift" caused by microstepping.
Build Author Michail Views 1199
x_y_module laser engraver
low cost 2 axis cnc laser, really portable and easily expandable
Build Author David Bourne Views 5378
INDY-TR12 CNC (12mm Diameter Lead Screws)
TR12x3 screws, M8 wheel sets, a draw built into the design, an electronics set built onto the kit, back brace to stop C-Beam twist.
Build Author openhardwarecoza Views 58320
openBuilds FreeBURN-1 V-slot CO2 Laser (60-100w)
DIY Lasercutter: Budget orientated, medium sized (60-100w), safety first, based on Lasersaur software toolchain
Build Author recoush Views 4375
CoreXY 3D build one
an 8020 build with 1010 extrusion (1") Square tubing Rough size is 24x24x36 (600x600x900) The expected usable print area 21.5x21.5X32"roughly (510x510x760) An XY 3D printer with 3 extruders and 3 Z-axis 0.9 degree motors the table (Z-AXIS) will lift up to the XY Carriage on 3 12mm linear rod and 3 8mm Lead screw's Corexy designs complete and Z-axis build is started don’t have a 3D cad system yet so building my prototypes on a pcb layout tool
Build Author Lasersc Views 7314
D&R Tiger Paw build combo
The Tiger Paw will be a 1000mm X 500mm Cartesian style CNC with the Minimill attached to the end. It is named the D&R Tiger Paw because my son, Daniel, and myself, Richard, will put this Tiger strong and fast machine together. Our goal is to have a Tiger strong build with a Paw print that wouldn’t take up a huge amount of space in our garage.
Build Author CChico Views 13969
Custom build 80w Co2 Laser Cutter
Building a custom made 80W Co2 Laser cutter. Making it from scratch and it's a work in progress but I've learned a lot and I'll be sharing a bit of that knowledge with you guys since I've learned a lot from here.
Build Author LukasK Views 10481
I have completed some custom build 3d printers (i3 and delta style) and a cnc mill based on v-slot and c-beam. From the beginning the cnc was built to fit/change between router, 5w led laser module and plotter pen. While all three works great, the build is primarily focused on heavy duty milling and brings some disadvantages when it comes to laser - slow because of leadscrew motion system and not as powerful because of “only” led laser. That is why I have started this build of co2 laser machine.
Build Author pek Views 41350
Prusa i3 Bear Upgrade V2
Stronger frame for Prusa i3 MK2(s), MK2.5 and MK3 3D printer
Build Author roadss Views 15105
Rawcnc 1.5 Desktop Edition
This will showcase the build of my Rawcnc 1.5. A rigid cnc router from the Swedish company Rawcnc, featuring a rather cool linear motion system, rack & pinion and steel reinforced X-axis capable of milling aluminum.
Build Author arcrunner Views 4908
Workbee 1015 (50" wide by 30")
A Workbee able to cut 48"x24" material, built to continuously feed material so one can cut full sheets of ply.
Build Author sgspenceley Views 88541
Linear Rail CNC Machines
A CNC build using linear rails & lead screws.
Build Author Chris Anderson Views 32856
Openbuilds Co2 80w Laser Cutter
Co2 80 watt openbuilds laser cutter, 1200mm laser tube, 1500x1000x500mm dimensions. Build frame first and then panels to be added.
Build Author CoreCube3D Views 10780
CoreCube3D - A CoreXY 3D Printer
Building a CoreXY based 3D printer using primarily parts from China on eBay. Large 500mm frame.
Build Author Patto21 Views 651
Large format laser
Large format laser build for Student use at my school as well as some personal use.
Build Author RV6APilot Views 1800
South Carolina Workbee 1000X1000
This is about my build of a Workbee 1000X1000 being built here in Trenton, SC. My goal is to use it to help cut the new panel for my RV6A airplane.
Build Author obmilllivebuild Views 4227
Live OpenBuilds MiniMill -> MiniPrint/Laser Conversion Demo @ MRRF2019
Transformation of an OpenBuilds Mini Mill into a convertible 3D printer / CNC mill with interchangeable tooling. Maybe a bonus conversion TBD.
Build Author Michael Morlan Views 2076
Shapeoko 2 - my first CNC
This was my first foray into CNC. I chose to go with a reliable kit build since my knowledge of GCode, controllers, and steppers was pretty rudimentary.
Build Author Ariel Yahni Views 2295
OB 2x72 Belt Grinder
Build a 2x72 Belt Grinder out of OpenBuilds V-Slots
Build Author joetemus Views 9679
K40 ACRO Conversion
A K40 to ACRO Co2 laser cutter build. Designed and built to expand the work area of the K40
Build Author JerwanDavis Views 2629
Coined by my family as the: Davomatic
Build Notes: Here are all the parts necessary to re-produce this design. Please note, all of the parts are either sourced through openbuilds or have been selected and printed from thingiverse.
Build Author Sonny Lowe Views 10117
MakerSL MSL-8 OB Vise
Small Machining Vise designed around 20x80 Openbuilds Rail System
Build Author Santoferr Views 4135
Butterfly 3DP V 1.0
tronxy x3 like
Build Author patnap71 Views 2422
MEGADELTA, TLM CLONE with 500MM bed
All metal frame 500mm bed Delta 3D printer
Build Author Dexter Oddwick Views 5875
Black Rabbit 1500
This is a router that I designed that is loosely based on the Openbuilds Ox, but designed to be heavy duty, rigid, and yet quick and agile.
Build Author Christian James Views 2752
Workbee "style" 1010 cnc
This build is based on the Workbee 1010 CNC. It is not a kit build and is much the same as the original but with some significant changes made here and there as the build progresses.
Build Author Joelosborn Views 791
Project Infinity co2 laser
1m x 1.8m 60w co2 laser build.
Build Author Ed Chung Views 3413
Rigidbot Big with glass bed
Started with a Rigidbot Big Added a single flat glass bed Used a Smoothieboard clone driving DRV8825
Build Author pedrofernandez Views 8052
The Franken Forty
This is a K40 machine conversion!!
Build Author Jacob Lotter Views 1403
CNC ESS Controls System
My Controls box to run my Workbee 1510 That was retrofitted with Lead Screws as well as Lineal Bearings. The stock electrical configuration was not enough, so here are the Measures that I took to not only make this machine Run again, but to have fun with it, and make this system be able to run any CNC I run in the future with the installed microcontroller.
Build Author Martin.Barfoed Views 75449
Large format 1200X1500mm OX Build using Stainless Steel plates, dual belt configuration. Limit switches is a mix of micro switches and NPN Proximity switches. Electronics based on parallel break out board, Long Motor Stepper drivers (Chinese stuff) and motors controlled by Mach3. Spindel will be Kress 1050.
Build Author joetemus Views 2302
Shapeoko 2 Z-Axis Upgrade
This is a major redesign to the Z-axis of an otherwise stock Shapeoko 2.
Build Author Lumberjack Engineering Views 12492
SOLAC: Space Optimized LAser Cutter
The Space Optimized LAser Cutter is a 40 watt CO2 laser cutter that supports a maximum part volume of 24" x 16" x 6.25". It consists of a V-slot frame + brackets/mounts designed to be 3D printed on a consumer desktop printer. Total cost of the machine is ~ $1,400 USD.
Build Author pedrofernandez Views 4388
K40 Cube Laser Cutter
The k40 cube is a laser cutter build using mostly stock parts of the chinese k40 laser
Build Author HPB Views 28482
A simple XY laser engraver/cutter
A simple low-cost XY plane laser engraver/cutter inspired by the Much 4 laser build, with minimal parts and assembly time. Uses standard off the shelf components in almost 90% of the build with the exception of the axes motor and wheel mounts which need to be 3D printed.
Build Author Rob Mahan Views 6949
Rob's C-Beam Machine XLarge
This is my first CNC router build, so I started with the OpenBuilds C-Beam Machine XLarge mechanical bundle, including four high torque stepper motors. I took my time with the mechanical build, sought and found some great help for my control system, and designed and built a custom cabinet to house everything.
Build Author Rick Holder Views 9841
Gantry Type CNC with Makita Router
The machine has met and exceeded my expectations on repeatability and accuracy. Cost was approx £600 including the Windows tablet.
Build Author David Bunch Views 9746
Delta 3d Printer using 3/4" Electrical Metal Tubing (EMT) for Horizontals & 2060 V-Slot for the Verticals and adding a tetrahedron at the top.
Build Author SCYBUCK Views 2694
KYO SPHINX a la' SCYBUCK
KYO SPHINX, CENTROID ACORN, GECKO 540, HALL EFFECT LIMIT SWITCHES, 2.2 KW, 24,000 RPM SPINDLE, WATER COOLED, 600 oz-in STEPPERS, INTENDED TO CUT ALUMINUM.
Build Author Dantheman Views 6282
This unit is made with openbuild v-rail and c-beam. using direct drive with lead screws. Nema23 motors
Build Author BNMaker Views 4228
A minimalist 2-axis A2 sized laser diode cutter/engraver. Designed to give the most function using the very least number of parts at the lowest price.
Build Author Carl Siren Views 3712
A home-made CNC-machine with a 1.5 kW air cooled spindle motor suitable for milling materials such as wood, plastic and soft metals. The work table is 650 mm wide by 700 mm deep and the maximum movement is set to 560 mm for the x-axis, 480 mm for the y-axis and 105 mm for the z-axis.
Build Author Indieflow Views 79216
A lightweight, portable, accurate 3D Printer that has a good sized print area and small overall footprint that is easy to build, with easy to source components. The design is OpenSource allowing those with the capability to make their own parts get up and running.
Build Author Julius Views 18727
OX Balls - 1605 Ballscrew Powered 1000mmx1000mmm OX derivative
1000x1000mm Ballscrew driven OX Derivative. Dewalt 611 spindle and TB6600 Drivers.
Build Author Sprags Views 1021
C-Beam Kyo Sphinx 10060
More stuff here.
Build Author Beam Views 5403
DIY Flywheel Camera Slider
My take on a non affordable slider.
Build Author TurfnSurf Views 2922
3-Axis Plywood CNC
Theoretical Working area: 38" x 24" x 6" Actual Working Area: 31" x 23.6" x 4" Positioning Accuracy: about 0.01mm
Build Author Axnfell Views 1035
WorkBee 1000x2000 ACME Screw Version
Hoping to build a WorkBee 1000 x 1000 (2000) from parts and not a kit, cannot afford the kit in full so going the long way round...
Build Author pedrofernandez Views 3642
The Acro Laser Machine Build
Build Author obmilllivebuild Views 3104
Live C-Beam Build @ MRRF2018
Contained within are links to our OpenBuilds sponsored C-beam Machine live build taking place at MRRF 2018 (Midwest Reprap Festival) on March 24 and 25, 2018. There will also be some build images and a few 3D printed STL items that were added.
Build Author sausagePaws Views 52577
Embroidery machine with XY belt and pinion drive.
A simple Embroidery machine using an XY belt and pinion drive to drive a hoop under a standard sewing machine. Needle timing, machine power and stepper control are all provided by a PIC processor. A tablet provides the higher level formatting required for communicating with the PIC chip.
Build Author Gooshpoo Views 5226
Gooshpoo's H style cnc machine
A cool project about my cnc machines unique style.
Build Author ymilord Views 19049
C-Beam Rigid - 'The Hog'
C-Beam Machine baseline build. DW618 Spindle. SuperPID. Gcode Controlled Mist Coolant. Rigid Work Surface. NEMA 23 (425oz-in) Leadshine 4 Axis Stepper Driver. LinuxCNC (MachineKit) Tool Touch Off Probe.
Build Author coxnugget Views 1359
Bedroom Builds (BrB) DIY CNC
So I am employed in the automotive industry and I walk by thousands of dollars of CNC products daily that are no use to me due to being a Technologist and not a machinist. So therefore with some research I found openbuilds and their great selection of products to build my own CNC. This CNC will consist of 4 axis one removable 360 degree axis for turning alongside a x axis table Y axis stationary gantry and a Z axis attracted to the Y axis linear actuator.
Build Author Rob Withoff Views 1868
Some enhancements of the basic mini-mill
Build Author Daniel.korneliussen Views 1499
Reprap prusa mendel i2 Frankenstein 2018 build
Mad plumbers choice what Else can i say?
Build Author pek Views 16789
Prusa i3 Bear Half Upgrade v1.0
Stronger frame for Prusa i3 MK2 / MK2s / MK2.5 3D printer
Build Author dmasters Views 5406
DM C-Beam XXL Tank
1000mm x 1000mm C-Beam XXL CNC with external drivers and high torque Nema 23 motors, 2.2KW Spindle with VFD.
Build Author Dave Pyatt Views 2061
DaveP's Homemade CNC Project
Somewhere along the line sometime around February 2017 I got the bug in my head that I needed to build a CNC router. This is where I am today...
Build Author RussB Views 4894
New 2 watt laser platform
Acro based 2 watt laser platform
Build Author BeTrue3D Views 14161
High Quality CoreXY with focus on quality and optimized printarea versus physical size of the printer.
Build Author Ronald van Arkel Views 12520
Upgrading the C-Beam machine
So we have new plates, stronger motors, belt drive reduction, but what should we do with them? In this article you might find the answer you were looking for as we took an “old” C-Beam machine and started to upgrade the X/Z body and added more torque and precision to the Z-axis.
Build Author JWhitten Views 9825
Build #2 - Bigger & Stronger
Large format CNC router with a 1500mm x 3000mm cutting envelope (5 x 10 ft) strong enough to cut wood and aluminum constructed from 20-series and 40-series aluminum extrusions. Complete Project Log w/ Pictures: https://goo.gl/photos/Co81AvGwVijE2zow9
Build Author Jens Grabner Views 2220
This calculator work inside with a spezail count format - Fraction as Mantisse + Dezimal exponent .. in summ 9 Byte.
Build Author Tucstrlly Views 5404
Stainless OX Kit Build "Diamondback CNC"
A copy of the Stainless Ox by Martin Barfoed. Similar design, construction and control.
Build Author ZacharyB Views 2011
Arizona OpenBuilds MiniMill CNC
I ordered the OpenBuilds MiniMill from the OpenBuilds Parts Store http://openbuildspartstore.com/ They were out of Motors and Electronics when I ordered so I had to source these items elsewhere. But it turned out well doing it this way.
Build Author Superslinky Views 4498
K40 Laser Build (Major Changes)
Major K40 Laser Mod
Build Author sybren Views 3697
80watt Lasercutter, workingarea 105x52[cm], steel frame
I will write a short buildlog here with mostly pictures. I designed this lasercutter in solidworks(not totally finished) for a good overview and such that the steel tubes could be lasercut by a company, the metal frame is based on the lasercutter the KÄSER, which you can find on cnczone.nl. The mechical parts are designed by myself because I had no mill to my use, so the mechnical parts are lasercut(same company as tube) steelplates welded together.
Build Author ymilord Views 12324
Small Portable PCB CNC Machine (CoreXY)
This is a small CNC mill/router specifically for manufacture PCBs. This is based on the corexy gantry setup. The plan is to have a small, light self-contained machine that can be used and easily but away when it's job is done.
Build Author dtanney Views 1864
This will be a CNC milling machine. My goal is to make this mill for the minimum cost I can while not sacrificing quality. In hope of staring an educational YouTube channel on CNC milling and 3D Printing. Along with when to use both.
Build Author ymilord Views 7768
Kyoujin Mk1 (C-Beam /w Rack & Pinion)
C-Beam based CNC with Rack & Pinion (for the X Axis) and lead screws (for the Y Axis)
Build Author Elijah Anderson Views 6734
The Budget Build
An affordable large CNC machine, that so far has been easy to assemble
Build Author stargeezer Views 6974
OXilla - a 3ft x 3ft CNC Router/Mill - Goals are strength, power and speed
This will be an ongoing log as I build this machine. Name change by popular demand - at least a couple of us. :)